Meade autostar controller troubleshooting

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING HOW TO
MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING PDF
MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING UPDATE
MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING MANUAL
MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING BLUETOOTH

These parameters include the tracking, guiding and Fortunately, the keypad supplies these parameters even You should beДЄware that there are additional parts of the initialization sequence that That StarGPS will be initializing your mount, not the keypad. The instructions below will have you set your Auto-Connect to EXT. Necessary in the keypad as long as the keypad can correctly calculate UT, which Used to converting local time to UT and vice versa. This should not really pose a problem for astronomers, since we are quite Will also need to remember that the keypad will now only show UT as the local The keypad must be set to '00' since the entered local time is UT. Without using StarGPS, but your time zone for ALL of your entered locations in You can still have locations entered into the keypad, for quick setup at home Up his or her keypad in the morning might need to remember that it is still So tomorrow's date could be the correct entry. Might be setting up in the evening, UT may already be into 'tomorrow,' Into the keypad as well! For example, for those of us in the US who Savings setting at '0.' Be sure that you put the correct UT date GTO keypad, simply input the GMT as your local time, and keep the Daylight Universal Time or GMT if you will be using StarGPS. To easily solve this potential problem, ALWAYS keep your keypad set to The mount, so it is important that you follow these instructions. Either of these situations can result in the scope being driven into Very close to the meridian, and they will affect park position calculationsДЄdversely. Normal go to operation during a night of observing, they can affect syncs done Potential for timing issues that affect precise calculation of the meridian The GPS uses Universal Time, and the keypad starts from local time, there is the System, we recommend that you change the way you have your keypad set up. Note: For the most efficient use of StarGPS with your Astro-Physics GTO StarGPS-NX uses the Meade LX200 Command Set to send GPS data to the GTO. * Early model GPS-NX01 and GPS-NX02 receivers may specify 9600 baud.

Note that the local date and time are set to UTC (Coordinated Universal Time).

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING UPDATE

It is recommended to leave the GPS connected for at least twenty minutes following its first use (this allows it time to download and update the almanac and ephemeris data used to locate satellites, resulting in better performance After the telescope has accepted the GPS data it can be disconnected.Short-on blink every two seconds: telescope has accepted GPS data.This may not work indoors and normally takes about one minute Short-on blink every second: determined date, time, latitude and.Rapid blinking for 5 seconds: no telescope found, switching to 4800* baud NMEA.Older GPS-NX02 and GPS-NX01 receivers require a firmware update (contact us) to resolve this problem for use with StarSense handsets. Or detected Vixen StarBook in non-INIT state (requires power on/off reset). Rapid sustained blinking: detected old NexStar firmware (requires update).Short-off blink every second: determined telescope type.The GPS-NX01 and GPS-NX02 receiver status LED indicates:.The GPS-NX02 can also be used with the Meade LX200GPS, LX200R, LX200ACF, LX400ACF and RCX400. Gemini, Gemini-2 or Gemini-2 Mini, Astro-Physics GTO, Synta (Orion Atlas/Sirius, Sky-Watcher SynScan) and the NexStar, NexStar+, StarSense, Meade Autostar, Audiostar, LX200 Classic, Losmandy Adapter cables are available for use with Celestron StarGPS-NX includes a high-performance GPS

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING PDF

Start Instructions' which are in PDF format.

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING HOW TO

This section describes how to use StarGPS-NX.В You mayДЄlso wish to download a copy of the ' StarGPS-NX Quick

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING MANUAL

This User Manual discusses the setup and use ofДЄdditional information and tips on using the Meade Autostar and ETX/LXD telescopes I highlyДЇor more information on Celestron NexStar I recommend visiting:

MEADE AUTOSTAR CONTROLLER TROUBLESHOOTING BLUETOOTH

Using a Bluetooth or USB connected GPS Receiver.

Vixen StarBook, StarBook Type-S and StarBook Ten.

Synta (Orion Atlas/Sirius GoTo, Sky-Watcher SynScan).

Retired GPS-NexStar cable for use with older handsets.

Celestron NexStar, NexStar+ and StarSense (SLT, SE, AS-GT, CGE, CGEM, GT, Evolution, iSeries).

Meade autostar controller troubleshooting